![openbox v8s manual openbox v8s manual](https://ae01.alicdn.com/kf/Hbc60f0d694834ca6b3956e5e64169366G.jpg)
If you are using the DisEqC1.2 motor, then all you need to do is ignore the longatude and latitude options and simply click on Set Motor as DisEqC1.2 on all Satellites then exit. Setting up a multi satellite system, click Menu -> Installation -> Antenna and Satellite Quick Setting if your going to use the USALS motor setup the Longatude and Latitude options and click Set Motor as USALS on all Satellites then exit. If you add the *****.cfg file after you have done a scan, then you will be required to reboot the receiver for the the file to become activated correctly.
OPENBOX V8S MANUAL INSTALL
Now for the fun part, if you already have ***** you will need to import them to the receiver, to do this use a flsh stick formated in fat32 and place your *****.cfg file onto the flash stick, insert the flash stick into the usb socket on the rear of the receiver, then go into Menu -> Network Local Setting **** Plug Setting -> Update Files by USB -> SELECT OPTION 1 and click the yellow button to install your *****.cfg file, if all goes okay click exit and select Manage Config Files select option 1 now place a tick to each line you wish to activate, if for example you have 4 clines from a payserver activate all 4 lines you should then see online next to each line you activated with a tick, now you can exit the menu altogether, as you can now start to add satellites and channels. Now you will proberbly need to set your nework up, so again enter the Menu -> Network Local Setting and set DHCP to ON, if your router is not DHCP compatable you will need to manually configure the settings, once you have done that click Apply and exit. If your picture is not quite as good as you expect, try going into Menu -> System Setup -> Display Settings and change any of the following options, Brightness - Contrast - Saturation, once you have set them exit and your alterations will be stored.
OPENBOX V8S MANUAL FULL
The setting up of the receiver is simple enough, one thing you should beware of is the display settings, in the Menu select -> System Setup -> TV System -> Video Out here you get two options RGB & YUV, if you select RGB then you have only two resolution options 480i & 576i, there is also an Auto option, if you wish to access the full resolution options the set the YUV then you get them all the 50 and 60 options shown refers to the refresh rate of your television, so if your television refresh rate is 50Mhz then set the output to 50, for example you will the get a crystal clear picture.
![openbox v8s manual openbox v8s manual](https://image.dhgate.com/0x0/f2/albu/g5/M00/60/13/rBVaJFhsl82AaFJNAA2dFImOiRs881.jpg)
All fed from Sky dish with octo lnb, 80 cm dish with 2 quad lnbs for 13 and 19.2 (soon to be downgraded to 60cm dish and 80 cm upgraded to motorised with another quad - I have all necessary bits for this but need time to get up on flat extension roof and install) Combined DSAT/DTT receivers in bedrooms for freesat and Freeview (albeit without EPG). Sky HD, TM PVR, Openbox and analogue in my den along with Topfield Freeview PVR and DVD/HDD recorder with Freeview tuner built in. The setup is Sky HD, analogue receiver and generic PVR in lounge for my father. Most of my boxes were either donated (when I upgraded peoples systems) or cheap car boot sale/ebay purchases. In recent months I have given 2 Sky boxes to friends.
![openbox v8s manual openbox v8s manual](https://miro.medium.com/max/1400/0*1zrMfTvmlFRdS3Sf.png)
OPENBOX V8S MANUAL PLUS
In my shed/workshop I also have 2 Sky+, 1 standard Sky, 1 geneneric digital and 4 analogue boxes all working plus a few more waiting repair/disposal including 1 Sky HD box. Of these only 5 were purchased new (1 Sky, 1 Analogue and 3 PVRs. 9 at present in use with the new Openbox, 2 Sky HD, 3 PVRs, 2 Analogue receivers (purely for FTA Eurosport in English) and 2 combined DSAT/DTT receivers for the bedrooms.